B&L Cremation Systems Human Crematory N20 Retort

N20 Human Crematory


The B&L Cremation Systems, Inc. N20 human crematory is our low to medium production crematory, With cremation times of 120 minutes.
		Download Installation Manual

Specification

U.S Standard

Metric System

Length:

150"

3.8m

Width:

66" (76" With Control Panel)

1.6m (00m with control panel)

Height::

85" (96" With Doorcap)

2.4m (00" With Doorcap)

Weight:

22,000 lbs.

10,886 Kg

Door Opening

40" W x 29" H

0.7m H x 1.0m W

Clean Out Door Opening

21.750" x 19.750"

Gas Pressure:

Natural Gas 7" W.C.
Propane Gas 11" W.C.

Natural Gas 1.7 kPa W.C.
Propane 2.7 kPa W.C.

Power Requirements:

220V, Single Phase, 25 AMPS

Cremation Rate:

150 lbs/hour

68 Kg/hour

Body Weight Capability:

500 lbs

226 Kg

Stack Height From Grade:

Minimum 18'

5.4m

Stack Sections:

24" O.D

0.6m O.D

Chamber Dimensions:

Length: 94"
Width: 40"
Height: 34.5"
75.0 Cubic Feet

2.3m
1.0m
0.8m
1.84 Cubic Meters

Burner output:

Maximum Input Rating 1,500,000 BTU's per hour
Afterburner Maximum 1,000,000 BTU's per hour
(Full Modulation 100%)
Ignition Burner 300,000 BTU's per hour
Cremation Burner 500,000 BTU's per hour

Maximum Input Rating 1,582,500 KJ per hour
Afterburner Maximum 1,055,000 KJ per hour
(Full Modulation 100%)
Ignition Burner 316,500 KJ per hour
Cremation Burner 527,500 KJ per hour

Air Requirements:

Outside air inlet louvers in the room
located at or below burner height, capable
of passing 2,500 CFM of free air.

Outside air inlet louvers in the room located at or below burner height, capable of passing 1.173 Cubic meters per second

Features to the above unit

FULLY AUTOMATIC CONTROL SEQUENCE. Operation is made simple by the fully automatic control sequence. A microprocessor temperature controller, with a digital readout, ensures optimum control while providing the lowest fuel consumption. Visual verification of each stage is provided on the control panel. Operator override is achieved at a turn of a switch for semi-manual control.

HOT HEARTH DESIGN. First introduced by B&L, this design allows for wasted afterburning heat to be recycled through the floor, eliminating fluid problems, lowering fuel consumption and extending the hearth life.

MULTI-CHAMBER AIR CONTROLLED DESIGN. The entire combustion process is completed within the air controlled chambers eliminating burning in the stack, allowing for 24 hour operation and providing for greater fuel efficiency over excess air designs.

POLLUTION MONITORING & CONTROL SYSTEM. This system constantly monitors the stack gases to prevent visible emissions. Integrated with the automatic system, this feature enables the unit to make all necessary adjustments automatically.

REFRACTORY LINED STACK. A three inch insulating liner is provided as a safety feature. While gases seldom exceed 1000°F, the liner reduces heat penetration under every condition, preventing the possibility of fire. A ten year warranty is offered on the stack liner.

LOW NOISE. The secondary combustion blower has been manufactured and installed to allow for low noise operation.

HYDRAULIC LOADING DOOR. Push button operated, this feature enables the operator to open the door to the desired height from the control panel, an important safety feature for busy installations, providing better fuel efficiency and longer refractory life.

STAINLESS STEEL FRONT.** More than just aesthetics. Stainless steel is easy to clean, while providing a professional finish to your equipment...an important feature when considering a viewing.

REMAINS REMOVAL SYSTEM.** A separate remains removal door, located on the side of the unit, is included to enable the operator to push the remains to the rear of the chamber, reducing heat loss and thermal shock as the loading door needs only to be opened 6"- 8" for removal. A stainless steel cooling pan is located on the outside of the unit to prevent fluid contamination.

** Optional on N-20 & N-20SA

N20 Human Crematory

Features to the above unit